Opener repair guide
The Most Common Garage Door Opener Repairs
This is garage door opener repair as it really happens, counted from our own job records instead of guessed. Of 186 opener repair jobs, safety sensors came up most, then gears and drive parts, travel limits and force settings, and the arm and bracket hardware. Boards and motors were rare.
What this service covers
Real work by background-checked local technicians, quoted at a flat rate you approve before anything begins.
Safety sensors
Photo-eyes realigned, cleaned, rewired or replaced. This was the single most common opener repair in our records.
Gears, sprockets, chains and belts
Stripped drive gears, worn sprockets and loose or snapped chains and belts repaired or replaced.
Travel limits and force
Open and close limits reset and force adjusted so the door stops where it should.
Arm, bracket and hardware
Door arms, brackets and bolts that work loose and leave the opener pulling on nothing.
Boards, capacitors and motors
Electronics diagnosed and replaced where the opener is worth keeping. These were the rarest repairs.
From our job records
Counted from our own completed opener repair records, not including new openers or remotes.
- Opener repair jobs since 2017
- 186
- Typical time on site
- 39 min
- Busiest season (Mar to May)
- Spring
Time on site is the median of the 17 repair jobs with a logged start and finish.
- Sensors are the most common repair: 47 of 186 jobs.
- Boards, capacitors and motors are rare: 4 of 186 jobs.
- Most repair visits are short, about 39 minutes on site.
What the repairs were
- Safety sensors47 of 186 jobs
- Gears, sprockets, chain or belt21 of 186 jobs
- Travel limits or force21 of 186 jobs
- Arm, bracket or hardware19 of 186 jobs
- Board, capacitor or motor4 of 186 jobs
Quick checks before you call
Look at the sensors near the floor. A dark or blinking light usually means misaligned or blocked eyes.
Pull the emergency release and lift the door by hand. A heavy door points to springs, not the opener.
Listen to the opener. A hum or click with no movement can be a gear, a capacitor or a spring.
Check that the wall button works while the remote does not. That points to the remote, not the opener.
How it works
- 1
Call or book online
Tell us what the opener is doing. We schedule a same-day or next-day visit.
- 2
On-site check and flat quote
The technician checks the door and springs first, then the opener, and gives you a flat price to approve.
- 3
Done and tested
We repair the fault, reset the limits and force, and test the sensors before we leave.
Why homeowners call G Brothers
Voted Best Garage Door Company, three years running
And rated 4.9 stars across 400+ Google reviews.
More than 40 years of experience
Family-owned, locally operated, and BBB accredited.
Free, no-obligation estimates
We look, diagnose, and quote a flat price you approve before any work starts.
Same-day and 24/7 emergency service
Most repairs are handled the day you call.
Background-checked, licensed, and insured technicians
Local crews you can trust in your home.
No pressure, done right the first time
We recommend a repair over a replacement whenever that is the right call, and back it with a workmanship guarantee.
Reviews
Rated 4.9 across 400+ Google reviews
Homeowners and businesses trust G Brothers for fast, honest garage door work.
Based on 400+ Google reviews
Upfront, flat-rate pricing
Your estimate is free. We diagnose the problem on site, then give you one flat price to approve before any work begins. No surprises, no pressure, and an honest recommendation on whether a repair or a replacement is the better value. Free estimates cover garage door repair, spring, opener, and replacement work. Remote and keypad programming is quoted when you book.

Visit us
Find G Brothers Garage Doors
Reach out for same-day garage door service. Our technicians come to you for every repair, replacement, and install.
Our shop
7700 W 9th Ave, Lakewood, CO 80214
Open 24/7 for emergency garage door service.
Related questions
Quick answers about most common opener repairs and related work from the G Brothers team.
Why is my garage door opener not working?
Garage door opener not working? Check the power, remote battery, sensors, and travel limits first. Here is what is DIY-safe and what needs a tech.
Read full answerCan a garage door opener be repaired, or does it need to be replaced?
Most garage door openers can be repaired if a specific part has failed.
Read full answerMy garage door opener motor runs but the door won't move. Is it the gear?
Usually yes.
Read full answerShould I repair or replace my garage door opener's logic board?
Repair the logic board if the opener is under 8 years old and otherwise functional.
Read full answerHow do I adjust my garage door opener travel limits and force settings?
Travel limits tell the motor how far to drive the door open and closed.
Read full answerHow much does garage door opener repair cost?
How much does garage door opener repair cost? Most Front Range fixes run $100 to $350 parts and labor. Here is what each opener repair costs.
Read full answerWhy does my garage door opener keep tripping the GFCI outlet?
GFCI trips on a garage door opener are caused by one of three things: motor startup inrush current tripping a standard GFCI, a genuine ground fault from moisture or aging wiring, or the opener being on the wrong circuit.
Read full answerWhy is the light on my garage door opener not working?
The most common reason is a burned-out or wrong bulb.
Read full answerWhat kind of light bulb does a garage door opener take?
Most residential garage door openers use a standard A19 or A15 medium-base (E26) socket, the same size as a household lamp.
Read full answerWhy does my garage door opener light stay on?
A garage door opener light that will not turn off is almost always caused by the light timer being set too long, a stuck or shorted wall button, a triggered motion sensor, or a stuck relay on the logic board.
Read full answerMy garage door opener stopped working after a lightning strike. What's damaged?
After a lightning strike or surge, start with three checks: reset the GFCI outlet, check the circuit breaker, then unplug the opener for 60 seconds and replug.
Read full answerHow does the motion-activated light on a garage door opener work?
Garage door openers with motion-detecting light use a passive infrared (PIR) sensor built into the opener head to detect movement in the garage and automatically turn on the light.
Read full answerDoes my garage door opener need surge protection?
Yes, a surge protector is worth adding to any garage door opener.
Read full answerCan you adjust the speed of a garage door opener?
Most residential garage door openers do not have a user-adjustable speed setting.
Read full answerHow do I replace a garage door opener trolley carriage?
A trolley carriage replacement is safe for DIYers because the door is in the closed position and springs are not involved.
Read full answerMy garage door opener runs but the door won't move. What is wrong?
The opener motor runs and the trolley travels the rail but the door stays put.
Read full answerCan an LED bulb interfere with my garage door opener remote?
Yes.
Read full answerRelated services
Service areas
Most Common Opener Repairs across the Denver metro
G Brothers brings most common opener repairs to homes and businesses throughout the Denver metro. Find your city below.
Ready to get started?
Book same-day service or a free estimate. Available 24/7.
Learn more
Guides & resources
Learn more about most common opener repairs before you book.
- Garage Door Opener Repair: Why Your Door Won't Close All the WayIf your garage door won't close all the way, the most common cause is a misaligned or blocked safety sensor near the floor. Other causes include travel-limit settings, a binding track, or a failing opener.Read guide
- Garage Door Remote Not Working? How to Fix ItIf your garage door remote is not working, start with the batteries. A dead or weak battery is the cause about half the time. If fresh batteries do not help, the issue is likely the sensor, antenna, or a lost pairing.Read guide





