Commercial

Why won't my rolling fire door close?

Short answer

A rolling fire door that will not close usually has one of four problems. The release did not let go, because the fusible link is painted or greasy, its chain or cable is kinked or pinched, or a release arm has been tied, blocked or wedged. Something is binding the curtain, such as a bent guide, bent slats, missing endlocks, a hood rubbing the coil, or a ceiling, light or conduit attached to the door. The governor or closing mechanism is worn or dirty. Or the door was not reset correctly after its last test. Keep the door closed, never prop it open, and have it repaired and drop tested by a trained fire door technician.

Need a door looked at?

G Brothers services commercial and overhead doors for businesses across Lakewood and the Denver metro, with 24/7 emergency dispatch. Free estimate, and a flat price you approve before any work starts. Commercial garage door repair

A rolling fire door that will not close usually has one of four problems. The release did not let go, because the fusible link is painted or greasy, its chain or cable is kinked or pinched, or a release arm has been tied, blocked or wedged. Something is binding the curtain, such as a bent guide, bent slats, missing endlocks, a hood rubbing the coil, or a ceiling, light or conduit attached to the door. The governor or closing mechanism is worn or dirty. Or the door was not reset correctly after its last test. Keep the door closed, never prop it open, and have it repaired and drop tested by a trained fire door technician.

How a rolling fire door closes on its own

A rolling steel fire door works like any rolling steel door in daily use, but it also has an automatic closing system. A fusible link, two pieces of metal held together by solder that melts at a low temperature, holds the closing mechanism back. When the link melts in a fire, or a smoke detector or alarm release trips, the mechanism lets go and the curtain comes down by itself. A governor limits how fast it falls.

NFPA 80, the standard for fire doors, sets what a good close looks like: the door must close completely and rest on the sill or floor, and its average closing speed must be at least 6 and no more than 24 inches per second. A door that stops partway, crawls down or slams down fails.

What the symptom tells you

What the door doesMost likely cause
Does not move at all when releasedThe release did not trip: a painted, greasy or dusty link, a kinked or pinched cable, a twisted chain, a blocked raceway, or a drop or release arm tied, blocked or wedged
Starts down, then stops partwayThe curtain is binding: bent guides, bent or torn slats, missing or broken endlocks, a hood rubbing the coil, or something attached to the door assembly
Closes too slowlyA dirty, greasy or worn closing mechanism or governor, or the curtain dragging in the guides
Closes too fastA governor that is worn, damaged or out of adjustment
Stops short of the floor or leaves a gapA bent bottom bar, an obstruction at the sill, or a guide out of line
Closes on the first drop test, not the secondThe automatic closing device was not reset to the maker's instructions after the first drop

Why the release does not let go

The release is a chain of small parts, and any one of them can hold the door open. Links get painted over when a wall is painted, or coated with dust and grease in a warehouse. Cables get kinked or pinched behind a new ceiling or duct. Sash chain twists. And a release arm sometimes gets tied up or wedged by someone who wanted the door to stop dropping during a test or a move. DASMA's inspection guide lists every one of these as a fault to look for.

Why the curtain binds

A fire door's curtain has to slide freely in its guides with room to expand in a fire. A forklift strike that bends a guide angle or kinks a few slats, missing endlocks that let slats shift, or a hood or flame baffle bent into the coil can all stop it partway. So can anything that is not part of the fire door but was fastened to it later: a suspended ceiling, a light fixture, ducting, conduit or framing.

What you can safely check

  • Make sure nothing is stored in the doorway or leaning against the guides.
  • Look at the fusible links: they should be where the maker put them, visible, and not painted, greasy or caked with dust.
  • Look along the chain or cable: no kinks, no twists, nothing pinching it.
  • Look for anything attached to the door, the guides or the hood that does not belong to the door.
  • Look for a release arm that has been tied, wired or wedged.

Do not cut, tie or remove a link, do not adjust the springs or the governor, and do not drop the door yourself to see if it works. A drop test means releasing a heavy curtain and measuring its speed, and the door has to be reset correctly afterwards.

Can you keep using the door until it is fixed?

No. DASMA's guidance is that a fire door waiting for repair should be closed and stay closed until it is repaired, inspected and drop tested, and should never be propped open. Any other plan has to come from a trained fire door technician and be approved by your fire authority. Fire door repairs should be handled with urgency, because the opening is not protected while the door cannot close on its own.

What a fire door repair involves

A repair returns the door to its original approved condition. Repair parts must come from the original maker of the door. When the maker no longer makes the part, the whole fire door has to be replaced, with one exception: the operator, governor and automatic closing device can be replaced with a labeled retrofit unit where it is listed for that door and your fire authority accepts it. Bottom bars and guides have their own rules from the listing agency, so they are not swapped like parts on a standard commercial door.

After any repair, the door must pass two drop tests in a row: one to show it closes fully, and one to show it was reset properly. The technician's company and the building owner keep a written record of the results. For the yearly schedule and what the annual test checks, see how often a rolling steel fire door must be tested and fire door closing speed.

Fire door or regular roll up door?

Many fire doors double as everyday service doors, so it is not always obvious. A fire door carries a listing agency label, which inspectors look for on the bottom bar, and it has fusible links or a detector release and a governor. If your roll up door has none of those and simply will not come down, see why a roll up door won't go down or why a commercial door won't close.

How G Brothers helps

G Brothers services and repairs commercial rolling steel doors, including fire-rated doors, for warehouses and businesses in Lakewood, Denver and across the metro. We service and repair the curtain, barrel and bottom bar, with parts from the door's original maker as the fire door rules require. A trained fire door technician runs and documents the drop tests and the annual test. We dispatch 24/7 and can provide a certificate of insurance, usually within 24 hours. See roll up and rolling steel door repair, call (720) 421-6489, or ask for a free estimate.

Sources

Related questions

People also ask

How often must a rolling steel fire door be tested in Colorado?

Every fire-rated rolling steel door must receive a formal drop test once per year under NFPA 80.

Read full answer
How fast must a commercial fire door close to pass a drop test?

Under NFPA 80, a fire-rated rolling steel door must close at 6 to 24 inches per second during a drop test.

Read full answer
What are fire-rated commercial doors and do I need one?

Fire-rated commercial doors close automatically to slow fire spread at rated walls. Here is how they work and where the building code requires them.

Read full answer
Why won't my roll up door go down?

A roll up door that won't go down usually has a lock still on, too much spring tension, a bent guide or bottom bar, a snagged end lock, or a motor limit or sensor stopping it.

Read full answer

Have a garage door problem now?

Tell us what your door is doing and we will tell you what is likely wrong and what it costs. Same-day service across the Denver metro.